When it comes to internet problems, the Wavlink AC1200 setup is your best friend. It is always effective in eliminating dead zones in your home. The Wavlink WiFi extender Setup is the nicest part about using an AP. setup your network to provide for faster, safer, and more reliable internet access. Wavlink extenders work with all of your gadgets. Wavlink works with any device, including smartphones, smart TVs, and even Roku. We’ll go over the steps you’ll need to take to set up your Wavlink booster in this article.

Here are the instructions for configuring the Wavlink AC1200:

• Turn on your wavlink AC1200 after unpacking it.
• Wait for the power LED to turn solid green after pressing the power button.
• Remember to keep the booster close to the router.
• Connect using Ap extender setup ext.
• Launch any web browser and type Ap.setup or 192.168.10.1, then press the enter key.
• To log in, enter your personal information.
• Follow the steps to complete the installation.
• You can now unhook your repeater and relocate it to your new location.

That’s how you manually complete the wavlink AC1200 setup procedure. If you have any problems with the manual setup, let’s try the (WPS) setup.

Wavlink AC1200 configuration through WPS

Let’s have a look at another approach for establishing your Wavlink repeater, the WPS method, which is said to be the quickest and easiest. After completing the Wavlink AC1200 setup through WPS, you will be able to set up your extender in less than two minutes without providing a username, password, or SSID. Let us now examine how the WPS technique works.

Here are the instructions for configuring the Wavlink AC1200 through WPS:

• Start your Wavlink AC1200.
• Make certain that it is close to the home router.
• On your booster, press the WPS button.
• Now, on your home router, push the same WPS button.
• When it displays three steady green lights, it implies you have successfully configured your repeater.
• You can unhook the repeater and place it wherever you choose.

That is how you complete the wavlink AC1200 setup through WPS.

How to update firmware on my Wavlink AC1200?

You will need to upgrade the firmware on your Wavlink AC1200 in order to remedy any issues you may face when using your extender (whether it is not providing the desired speed or something else). It has additional security features as well as other new features that will help you resolve your concerns.

Follow the steps below to upgrade the firmware on your Wavlink AC1200:

• Start your Wavlink AC1200.
• Consider any mobile device.
• Navigate to Ap.setup.
• Select settings and then firmware upgrade.
• Follow the steps to complete the firmware upgrade operation.
• It will take a minute, so don’t unplug the booster in the meantime.

This is how to update the firmware on your Wavlink AC1200.

 Also read

• PixLink WiFi Repeater Setup
• Macard WiFi Repeater Setup
• Trifiboost wifi extender setup

How to reset Wavlink AC1200?

If you have forgotten your admin password or login and wish to recover it, you must do a Wavlink AC1200 factory reset on your booster. When you reset the Wavlink AC1200, it prepares your extender for a new setup procedure by wiping all of your personal information, like passwords, usernames, and SSIDs. To finish the factory reset process, a hard pointed device, such as a paper clip or a needle, is necessary.

To reset the Wavlink AC1200, follow the procedures below:

• Connect your Wavlink AC1200 to a power outlet.
• Under a little hole, look for the factory reset button.
• It might be found on the repeater’s side panel.
• Push the reset button with a paperclip for 8-10 seconds.
• It will reboot automatically in a few seconds.
• Your extender is now prepared for the new installation procedure.

If you still require assistance with your Wavlink AC1200, please contact us via our toll-free hotline or live chat. We are always here to assist you  in any problem.

FAQ